Kickback is the bar and chain’s sudden unaccepted upward movement, it occurs when a user misuses the chainsaw. Either due to user error or mechanical error. Sometimes, it turns out even more fatal.
But with proper safety precautions, you can safely cut branches. The pole saw is just like any other chainsaw, making it dangerous if you’re not careful. But one problem people face with it is the pole saw Kickback. However, this problem causes many injuries every year.
Causes And Effect Of Kickback On Chainsaw
In general, three situations trigger a chainsaw attack:
- The chain hits a hard object in the kickback zone.
- The tree pulls the chain strongly in the middle of the cut.
- Other factors are contributing to starting a chainsaw.
The Chain Hits a Hard Object In The Kickback Zone:
Your chainsaw has a part known as the “drainage zone.” It is named after this because the tip of a chainsaw is the most common part of a chainsaw that can cause kicks.
Since this part of the chainsaw has the highest risk of being kicked, you should never use this part of the chain for cutting. Moreover, it raises the risk of serious stairs.
The Tree Pulls the Chain Strongly in the Middle of the Cut
Sawing with a chainsaw and a tree securely attached to the chain can cause collisions. That’s why it is always best to make a plan before cutting the block or blocks so that the chain does not push.
As a newbie to a chainsaw, your instincts can tell you to cut a branch or tree trunk at the same time. But this can be dangerous due to the possibility of confusing the chain when cutting. Therefore, you want to make two cuts, not one, to stay safe when using your chainsaw.
Other Factors Contributing to the Pole Saw Kickback
While the first two things we’ll look at are the main factors in the chainsaw tilt. Also, several other factors can increase your chances of pole saw Kickback. These include:
- If you don’t maintain the saw properly
- Cut with fuzzy chain
- The necklace trend is very relaxed
- Incorrectly installed circuit components
- Cracked, bent, or broken parts of the chain
- Suppose you don’t sharp the edge of the chainsaw
- Therefore, always use a high-quality chainsaw scraper
- Excessive chain depth adjustment
- Incorrect shape of the chain depth gauge
- Loose rivets.
Tips for Avoiding Kickback Chainsaw
How do you stop a chainsaw kickback?
To-Do 1:
Read the entire user manual before using your new chainsaw.
To-Do 2:
Always be careful while using your chainsaw. If you feel tired, it is not the appropriate time to use the tool.
To-Do 3:
You should be especially careful when you cut tree limbs. During desalination, a kick can occur, if the end of the rod hits trunks, tree stubs, unseen brushwood, and the end of the boxes.
To-Do 4:
Use the bottom of the saw (also called the tension chain) when preparing the tree for sawing. You should not put the saw above shoulder level. The risk of Kickback will reduce following these two methods when cutting plants and cutting stuff (shrubs, small trees) on the road.
To-Do 5:
If you choose a saw for trimming or cutting, drilling a sharp chainsaw edge into the stalk may be the best method to cut. The best technique to escape impacts is to avoid pressing the saw blade against a tree.
To-Do 6:
Ensure the chain brake is responding on your saw before usage.
To-Do 7:
Scratch the edge of the chainsaw and how to set it up.
To-Do 8:
Select the chains with a low angle saw. When buying a chainsaw, choose the one that suits you best and has the least chance of getting hit.
To-Do 9:
You should use narrow-edged rods like Oregon Double Guard rods for the highest impact protection.
To-Do 10:
Wear appropriate clothing and equipment to protect frequently injured areas:
– Chainsaws
– Hand Gloves
– Glasses (goggles or mask)
– Helmet Hearing protection (headphones or earphones)
– Protective boots like wooden ones.
To-Do 11:
Ignore the clothes which are too loose or too tight.
To-Do 12:
Ensure your fingers and thumbs are covering around the chainsaw hand grips during cutting.
To-Do 13:
Follow all directions which came with the chainsaw while executing maintenance. It will help to lower the risk of injury.
Can a Pole Saw Cut down a Tree?
Pole saws are designed to cut through branches, not trunks. That’s why there is a very limited amount of pole saw models that can actually cut down a tree. The ones that can are typically only made for cutting smaller trees.So, if you have your heart set on using a pole saw to take down a tree, you may want to consider finding one of these specialty models.
