If your Poulan chainsaw won’t stay running, there are a few things you can check to troubleshoot the issue. Make sure that there is fresh fuel in the tank and that the carburetor is clean. If the saw is still not staying running, the problem may be with the ignition system.
Check to see if the spark plug is fouled or if there is corrosion on the wires leading to the plug. You may need to replace the plug or clean the wires to get your chainsaw running again.
If your Poulan chainsaw won’t stay running, there are a few things you can check to troubleshoot the problem. First, make sure that there is enough gasoline in the tank. If the tank is empty or nearly empty, fill it up and try starting the chainsaw again.
Next, check the air filter. If it’s dirty, replace it with a clean one. A dirty air filter can restrict air flow to the engine, causing it to run poorly or not at all.
Finally, take a look at the spark plug. If it’s fouled or damaged, replace it with a new one. A bad spark plug can prevent the engine from starting or cause it to run rough once it’s running.
If you’ve checked all of these things and your chainsaw still won’t stay running, take it to a qualified repair person for further diagnosis.
Credit: www.reddit.com
Why Does My Poulan Chainsaw Dies When I Give It Gas?
Your Poulan chainsaw may be dying when you give it gas for a variety of reasons. The most common reason is that the carburetor is dirty and needs to be cleaned. Another possibility is that the spark plug is fouled and needs to be replaced.
If these two things don’t solve the problem, then it’s likely that there is an issue with the fuel line or fuel filter.
How Do You Fix a Poulan Chainsaw That Won’T Stay Running?
If your Poulan chainsaw won’t stay running, there are a few things you can do to try and fix the problem. First, check the spark plug to see if it is fouled or damaged. If so, replace it with a new one.
Next, clean or replace the air filter if it is dirty. Finally, check the fuel mix to make sure it is correctly mixed and not old or stale. If all of these things check out and the saw still won’t stay running, take it to a qualified technician for further diagnosis and repair.
Why Does My Poulan Pro Chainsaw Keep Shutting Off?
If your Poulan Pro chainsaw keeps shutting off, there are a few possible reasons. First, the saw may be getting too hot. This can happen if the air filter is dirty or if the engine is overworked.
To fix this, clean or replace the air filter and give the engine a rest. Second, the fuel mixture may be incorrect. The correct ratio is 50:1 (fuel to oil), so make sure you’re mixing it correctly.
Third, the spark plug may need to be replaced. If it’s fouled or damaged, it won’t fire properly and will cause the saw to shut off. Lastly, there could be an issue with the carburetor.
If it’s not adjusted properly, it can cause all sorts of problems, including shutting off mid-use.
If your Poulan Pro chainsaw keeps shutting off and you’ve tried all of these things without success, then take it to a qualified repair person for further diagnosis.
Why Does My Chainsaw Start But Not Stay Running?
If your chainsaw starts but won’t stay running, there are a few possible causes. The most common cause is that the chain is not properly lubricated. This can be remedied by adding more oil to the chain.
Another possibility is that the air filter is dirty and needs to be replaced. Finally, it could be that the spark plug is fouled and needs to be cleaned or replaced.
Poulan chainsaw won't idle
Poulan Chainsaw Troubleshooting
If your Poulan chainsaw isn’t working properly, there are a few things you can do to troubleshoot the problem. First, check the chain to make sure it’s not dull or damaged. If the chain is in good condition, check the bar and sprocket to see if they’re worn out.
If they are, replace them. Next, check the air filter to see if it’s clean. If it’s dirty, clean or replace it.
Finally, check the spark plug and carburetor to make sure they’re working properly. If all of these parts are in good condition and the chainsaw still isn’t working properly, take it to a qualified service technician for further diagnosis.
Poulan Pro 42Cc Chainsaw Starts Then Dies
If your Poulan Pro 42cc chainsaw starts then dies, there are a few potential issues that could be the cause. First, check the spark plug to make sure it is clean and in good condition. If the spark plug looks fouled or damaged, replace it with a new one.
Next, check the air filter to see if it is clean or needs to be replaced. A dirty air filter can restrict air flow to the engine, causing it to run poorly or stall. Finally, check the fuel mixture in the tank.
The correct fuel mixture for a Poulan Pro 42cc chainsaw is 50:1 (gasoline to oil). If the mixture is too rich or too lean, it can cause starting and running problems.
Poulan Chainsaw Carburetor Adjustment
If you’re a fan of cutting wood with a chainsaw, then you know that having a well-tuned chainsaw is important. And part of keeping your chainsaw in good working order is making sure the carburetor is properly adjusted. In this blog post, we’ll show you how to adjust the carburetor on your Poulan chainsaw so that it’s running at peak performance.
The first thing you need to do is locate the carburetor adjustment screws. On most Poulan chainsaws, these are located on the back of the carburetor, near the bottom. There are usually two screws: one for idle speed and one for fuel mixture.
With the engine turned off, begin by adjusting the idle speed screw. This controls how fast or slow the engine runs when idling. Turn the screw clockwise to increase idle speed or counterclockwise to decrease it.
After making an adjustment, start the engine and let it run for a minute or so before checking to see if the new setting has taken effect. If not, make another small adjustment until you get it just right.
Next, adjust the fuel mixture screw.
This adjusts how much fuel and air mix together in the carburetor bowl. Again, turn clockwise to lean out (less fuel) or counterclockwise to richen up (more fuel). As with idle speed adjustments, make small changes and then test-run your saw before making further adjustments.
You’ll know you’ve got it when your saw runs smoothly without bogging down under load.
That’s all there is to adjusting your Poulan chainsaw’s carburetor! With a little time and patience, you can keep your saw running like new year after year – ensuring that every woodcutting job goes off without a hitch!
Poulan Chainsaw Factory Carb Settings
If you’re a chainsaw user, then you know that having a well-tuned carburetor is essential to optimal performance. So, if you’re looking for information on how to properly adjust the carburetor on your Poulan chainsaw, then this blog post is for you!
First things first, let’s talk about what the carburetor does.
The carburetor is responsible for mixing the air and fuel in the correct ratio so that it can be burned efficiently in the engine. If the mixture is too rich or too lean, it can result in engine damage or poor performance.
Now that we know what the carburetor does, let’s talk about how to adjust it.
There are two screws on the carburetor that control the mixture – the low speed screw and the high speed screw. To adjust these screws, you will need a screwdriver and a tachometer.
The low speed screw controls the mixture at idle and should be turned clockwise until the engine starts to run rough.
Then, turn it counter-clockwise until it runs smoothly again. The high speed screw controls the mixture at full throttle and should be adjusted in a similar manner as the low speed screw – turned clockwise until it runs rough and then counter-clockwise until it runs smoothly again.
Once both screws have been properly adjusted, your Poulan chainsaw should be running at peak performance!
Conclusion
If your Poulan chainsaw won’t stay running, there are a few things you can check to try and fix the problem. First, make sure that the chain is properly lubricated. If it’s not, then the saw will overheat and shut off.
Second, check the air filter to see if it’s clean. A dirty air filter can also cause the saw to overheat and shut off. Finally, make sure that the spark plug is clean and properly gapped.
If any of these things are not working properly, then your saw will not stay running.
