If the chainsaw chain is damaged or worn, it will need to be replaced. Follow these steps to remove and install a new chainsaw chain.
1. Use a wrench to loosen the bar nuts that hold the chainsaw bar in place.
2. Remove the old chain from the bar and discard it.
3. Wrap the new chain around the bar, making sure that the teeth are facing the correct direction.
4. Pull the ends of the chain together and secure them with the master link.
5. Tighten the bar nuts to secure the new chain in place.
How To Put A Chain On A Chainsaw Properly
- Using a wrench, loosen the bar clamp bolt and slide the bar to the left until it is free from the chainsaw
- Remove the old chain from around the bar and discard it
- Unpack your new chain and wrap it around the bar, making sure that the teeth are pointing in the correct direction
- Pull the ends of the chain together and fit them into one of the links so that they lock in place
- Slide the bar back into place on the chainsaw and tighten up the clamp bolt with your wrench to secure it in place
How to Change a Chainsaw Chain | Stihl
If you’re a homeowner with some experience using power tools, changing the chain on your Stihl chainsaw is a fairly straightforward process. Here’s what you need to do:
1. Unplug the saw and remove the bar cover.
2. Loosen the bar nuts and remove the bar.
3. Remove the master link from the old chain (if present). If not, use a pair of pliers to break open one of the rivets that hold the links together.
Then, slide out each individual link until the chain is free.
4. Install the new chain onto the bar, making sure that it is positioned correctly according to the markings on both the bar and chain. If there is a master link, connect it now; if not, reconnect all of the rivets (using a hammer or tool designed for this purpose) to hold everything in place.
5 Hand-tighten The Bar Nuts And Replace The Cover 6 Plug In The Saw And Test It Out!
With just a few simple steps, you can easily change out an old chainsaw chain for a new one – and be back to tackling those backyard projects in no time!
Credit: www.instructables.com
How Do You Replace a Chain on a Chainsaw?
If your chainsaw chain is damaged or dull, it’s important to replace it as soon as possible. A dull or damaged chain can cause the saw to bind and kickback, which can be very dangerous. Replacing the chain is a relatively simple process that anyone can do with a little bit of knowledge and the right tools.
In this article, we’ll show you how to replace a chainsaw chain in just a few easy steps.
First, you’ll need to remove the old chain from the saw. To do this, start by loosening the nuts that hold the bar and cover in place.
Then, slide the bar and cover off of the saw so you can access thechain. Use a pair of pliers to break the rivets that hold the old chain together, then remove it from the saw. If your new chain is too long, you can adjust its length by removing links with a pair of bolt cutters.
Once you have your new chain, it’s time to install it on the saw. Start by threading one end ofthe new chain throughthe guide bar from underneath.
How Do You Change a Chain on a Stihl Chainsaw?
Assuming you need to replace the chain on your Stihl chainsaw, follow these steps:
1. Begin by ensuring that the saw is turned off and cooled down. Removing a hot chain can cause serious burns.
2. Next, remove the bar cover, which is located at the front of the saw near the tip of the bar. On some models, you may need to unscrew a couple of screws to do this; on others, the cover simply snaps off.
3. With the cover removed, take out the old chain and discard it.
4. To put on the new chain, feed it around both sprockets (the small wheels inside the housing that hold onto and drive the chain). The teeth on both sprockets should be pointing away from each other as you do this—if they’re not, flip one of them over so that they are.
5. Once the new chain is in place around both sprockets, pull it tight and ensure that there’s about an inch or two of slack—any more than that and it could come loose while you’re using it; any less and it could snap under tension.
6. Finally, reattach the bar cover (snapping it into place or screwing it back on) and you’re good to go!
How Do You Relink a Chainsaw Chain?
If your chainsaw chain has come off, or if the links have become disconnected, you’ll need to reconnect it before you can continue using the saw. Thankfully, this is a relatively easy process that only requires a few tools. In most cases, all you’ll need is a pair of pliers and a hammer.
First, lay the chain out on a flat surface so that you can see all of the links. If any of the links are bent or twisted, use your hands to straighten them out. Once all of the links are aligned, begin connecting them by fitting one link into another.
Use your pliers to gently squeeze the two ends of each link together until they’re flush. You may need to use your hammer to tap them into place if they’re being stubborn. Once all of the links are connected, give the chain a tug to make sure that it’s secure before putting it back on your chainsaw.
How Do You Change a Chain on a Craftsman Chainsaw?
If you find that your Craftsman chainsaw is not running as smoothly as it used to, it may be time to change the chain. This is a relatively easy process that anyone can do with a little bit of know-how. Here are the steps you need to take to change the chain on your Craftsman chainsaw:
1. Unplug the saw from the power source and make sure that it is turned off.
2. Flip over the saw so that you can access the bottom of the bar.
3. Use a wrench or pliers to loosen the bar nuts so that you can remove the bar cover.
4. Take out the old chain and inspect it for wear and tear. If necessary, replace it with a new one.
5. Put the new chain around the sprocket and make sure that it is installed correctly.
6. Reattach the bar cover and tighten down all of the nuts securely.
Conclusion
If your chainsaw isn’t cutting like it used to, the problem might be the chain. In this post, we’ll show you how to change a chainsaw chain in just a few easy steps. First, make sure the saw is turned off and unplugged.
Then, use a wrench to loosen the bar nuts. Next, remove the old chain and install the new one. Finally, tighten the bar nuts and you’re ready to go!
